 |
|
|
|
Home |
Memory |
Information |
|
|
|
|
Home |
Memory |
Information |
|
|
 |
 |
|
|
Beebe Speedway 2006 Hobby Stock Building Rules THOSE ITEMS NOT ADDRESSED IN THE FOLLOWING MUST REMAIN STOCK AS PRODUCED BY THE ORIGINAL MANUFACTURER BODY: 1. Any year model American made car. No front wheel drives allowed. Wheelbase must be factory stock. No tolerance. No subcompact cars. Rack and pinion cars must be factory stock parts only. If chassis is altered or steering parts are not stock and in stock location - it’s not legal! All uni-body cars must be tied together. Must have a complete stock factory floor pan and firewall. Trunk area may be cut no further forward than pinion of rear end. Seats must be in stock location. 2. Complete stock bodies and frame for that year model. Stock floorboards, rear fender wells and firewalls. Body must look factory stock, may use sheet metal (STEEL OR ALUMINUM) on doors and fenders. NO plastic or sheet metal on rocker panels or fenders. NO side skirts or plastic or sheet metal on windows (except sunscreen (5inch) on front window). NO ground effects on nose pieces. Bumpers may be square tubing ~ must run inner rub rail ~ minimum size 1 ½ inch round tubing on rear bumper. Must have tow loops front and rear. Spoilers must not exceed 6 inches. 2 braces allowed, one at each end and cannot exceed 6” in length. Spoiler must not be wider than trunk lid. Back of body must be enclosed fender to fender. Rear fender wells may be cut out for tire clearance, must maintain inner fender well that attaches to floor pan. Factory stock OEM frame front to rear. NO alterations allowed. This includes all cross members. Hood and trunk must be pinned down. Stock steel hoods or fiberglass hoods. Factory trunk lid or stock appearing aftermarket trunk lid. Front fender wells may be unbolted and removed. Fenders may be trimmed for tire clearance. 3. All weight must be added in the form of roll bars or solid weights bolted securely to the frame of the car outside of the driver’s compartment. All weights must be painted white with car number on it. 4. All doors must be secured to body. Must have stock appearing hoods and trunks. All window openings must remain factory size. Must have 3 bars in front of driver’s window. All cars must have front dash in stock location. Sheet metal only. Rear firewall must extend from bottom of rear window to bottom of floor pan. Holes in firewall must be covered with metal or aluminum. NO ENCLOSED INTERIORS. May replace factory dash with aluminum ~ no wider than 12 inches. 1/8” thick doorplate is mandatory. 5. All glass must be removed, including head and taillights. No rear view mirrors allowed. 6. Gauges may be removed. All flammable interior (carpet, headliner, interior side panel, rear seats, etc.) must be removed. Racing seat strongly recommended. Wiring harness may be removed and replaced. Shoulder harness is mandatory. All cars must be equipped with racing safety-approved seat belts bolted to the frame. No standard auto safety belts allowed. Neck brace and window net (or arm restraints) are mandatory. 7. Quick release steering wheel is optional. Quick steer boxes OK. Steering remains in stock position. 8. WEIGHT: 3400 lb. after race with driver. Top 5 cars weigh after heat races. Last chance transfer spots will weigh. Top 5 will weigh after “A” feature. ENGINE AND DRIVETRAIN: ENGINE MUST HAVE BEEN AVAILABLE IN THIS VEHICLE. YEAR MAY BE INTERCHANGED. MUST HAVE 360 DEGREE EXPLOSION PROOF STEEL BELLHOUSING 1. Engine must be stock production. Factory blocks only. No 90 or newer roller cam blocks. No bowtie or aluminum blocks. Casting numbers must be readable by tech official. No 400 blocks. Engine set back #1 plug even with upper ball joint. Flat top or dished pistons only. Maximum cubic inch displacement to include clearance and wear is 362 for GM and Ford and 370 for Mopar. All others must not exceed 362 CID. 2. INTAKES: Any production cast iron intake or bow tie cast iron intake. No porting of the heads or gasket matching of intake or heads. Intake may NOT be reworked under carb area. Carb spacer no taller than 1 ½ inch allowed. CARBURETORS: 4412 Holley 2 barrel or stock factory carbs. 2-barrel only. Bottom throttle plate hole 1 11/16 inch. Top 1 3/8 inch. Factory style HEI distributors. No remote coils on GM distributors. No onboard electronic devices capable of storing information allowed. No aftermarket electronic amplifying devices allowed. Tachometers only. 3. Hydraulic camshafts only. NO flat tappet cams or mushroom cams. No roller hydraulic cams. Engines must not pull less than 14” of vacuum at 1000 RPM’s. All cars will be checked in tech. Zero valve lash is required. 4. Heads must be stock OEM production only. No aftermarket heads. Casting number must be readable by tech official. 2.02 - 1.60 valves in GM is the largest size allowed. No aluminum heads or angle plug heads. Aftermarket valve springs OK. Stock OEM rocker arms only. Screw in studs allowed. 5. Headers are legal. Must have mufflers securely fastened to headers. 6. Factory stock automatics or standard transmissions. Must use factory stock OEM clutch disc and pressure plates on stock steel OEM flywheels only. NO EXCEPTIONS. Stock type factory torque converters required on all automatics. Driver must be able to put car in gear from park/neutral and move forward and reverse at time of inspection. Must have drive shaft loop. Drive shafts must be painted white. 7. There is a $125.00 teardown rule on each: pistons, cams, lifters, rockers & porting heads and intake; flywheels/clutch; driveline. Driver only may protest. $25.00 of the money goes into the driver’s point fund. 8. CLAIM: $350.00 cash and swap. $50.00 goes to wrecker for pulling engines. Driver claiming must have raced at BEEBE Speedway in the Hobby Stock class the previous 2 feature events. LONG BLOCK ONLY. Anyone wishing to make a claim must have finished the feature on the night of the claim. Only the top 4 finishing cars may be claimed. Claimant must be on lead lap. To claim, you must go to the infield and hand the cash to the officials within the 5-minute protest period. If you leave the track, your claim is void. If you refuse to swap, or refuse the teardown rule, you lose all money won that night and all accumulated points. Second refusal, driver will be suspended for 3 weeks. Promoter may claim any engine following feature so long as claim is made within the 5-minute time limit. No driver may claim more than 1 engine during racing year. Claimed engine will be marked and must be run upon return to BEEBE Speedway. If “marked” engine is not run upon first visit back to BEEBE, you will not be able to run until motor is placed in car. SAFETY REGULATIONS: 1. Roll cages are required. No screw joint fittings allowed. The minimum requirement for all roll cages on all cars shall be an “A” shaped affair, constructed of at least 1 1/2” OD pipe with bars running from the upper right corner to the lower left corner, and just the opposite on the other side, forming a “X” as viewed from front to rear. There must also be a cross bar on top of “A” and 4 bars down the side and 4 bars around the top to complete a caged affair around the driver. All roll bar pipes must be at least .095 in thickness. Must have 3 kidney bars on the driver side and 2 bars on the passenger side. FOR 2006 ~ MUST HAVE 4 BARS ON DRIVER’S SIDE. The driver and passenger doors inner liner only may be altered as necessary to install bars in the door area. No further gutting allowed. Gussets required. Bars may be added to protect radiator and gas tank areas. 3 1/4 inch bars in front of driver’s window are mandatory. 1/8” doorplate is mandatory. 2. Gas tanks must be in stock position. Fuel cells mandatory. 32 gallon maximum. Gas tanks/cells must be securely installed with 2 inch wide by 1/8 inch steel straps. Pump, racing or aviation gas only. NO nitrous oxide allowed. TIRES - WHEELS - SUSPENSIONS: 1. IMCA, Street or track tires only. Any asphalt takeoffs on the front and rear. NO tires softer than a 55 compound allowed. NO recaps. 275/60/15 largest street tire allowed. All tires must pass tech inspection. 2. Steel racing wheels only. Maximum width is 10”. Right rear bead-lock recommended. NO plastic or aluminum wheels. 5/8” stud mandatory. 3. Racing springs allowed on front and rear. Adjustable/Cheater weight jacks on front only. Rear Springs must use stock upper spring pads in stock location. 4. Racing shocks allowed, must mount in stock location. No heim mounted shocks allowed. Must Have 3 or 4 wheel brakes, valve must be in engine compartment. After-market brake pedals and master cylinders are OK. Rear suspensions must mount up factory stock. NO alterations. All control arms must mount up in stock positions. NO aftermarket control arms. No Johnny joints. Any stock American made car or ½ ton truck rear ends allowed. All cars must remain on stock suspension for the car that it is under. NO gold tracs or any form of traction devices allowed. All rear ends must be locked. 5. A 9 inch Ford housing highly recommended. GRAND NATIONALS OK. GM rear ends MUST have axle retention. | 2006 Economy Mod Building Rules | 2006 Street Stock Building Rules | 2006 Modified Building Rules | 2006 Mini Stock Building Rules | 2006 Hobby Stock Building Rules | | Beebe Speedway 2006 General & Safety Rules | 2006 Schedule | 2006 Pay Scale | 2006 Prep | 2006 Winners Lane | 2006 Cars & Drivers | Beebe Mud Trucks | 2006 Champions | | Beebe Speedway 2010 Schedule | Winners Lane 2010 | Beebe Speedway 2010 | 2010 Pay Scale | 2010 Points | History | Beebe Speedway 2002 | Beebe Speedway 2003 | Beebe Speedway 2004 | Beebe Speedway 2005 | Beebe Speedway 2006 | Beebe Speedway 2007 | Beebe Speedway 2008 | Beebe Speedway 2009 | | Return Home | In Memory | Archives | Contact Information | |
||
 |
 |
